ring grooves造句

• Aerospace series - o - ring grooves - dimensions
  航空航天系列. o形密封环凹槽.尺寸
• Most pistons have three ring grooves at the top
  大多数活塞的顶部有3个活塞环槽。
• Aerospace series - o - ring grooves - dimensions
  航空航天系列. o形环槽.尺寸
• The grooves into which they fit are called ring grooves
  安装活塞环的凹槽称为活塞环槽。
• The sections between the ring grooves are called ring lands
  活塞环槽之间的部分称为环带。
• Round wire snap rings and snap ring grooves for shafts and bores
  轴和孔用圆钢丝挡圈及挡圈槽
• Felt rings , felt strips , ring grooves for rolling bearing housings
  滚动轴承座用毡垫圈.毡带和环形槽
• Chamfer and ring groove of thread hole
  螺纹孔的倒角和环槽
• Piston ring groove cleaning tool
  活塞环槽沟清洁工具
• Ring groove carbon remover
  活塞环槽积炭清除工具
• Securing parts for rolling bearings ; snap rings for bearings with ring groove
  滚动轴承用紧固零件.带环槽轴承用挡圈
• Aerospace series - o - ring grooves - dimensions ; german and english version en 3748 : 2001
  航空航天系列. o形密封圈凹槽.尺寸;德文和英文版本e
• Piston ring grooves are machined to piston ring manufacturer ' s specifications
  根据制造厂家的说明书要求，在无任何损伤的情况下将连杆从活塞上拆下。
• Piston rings up to 200 mm diameter for reciprocating internal combustion engines - ring grooves
  往复式内燃机用直径小于等于200mm的活塞环.第5部分:环槽
• Sometimes , all that is required is to free up the rings in the ring grooves by cleaning out carbon
  有时,所要做的仅仅是清除积碳,使活塞环在活塞环槽中活动自如。
• The molded ptfe ring is bonded into a seat ring groove in the face for maximum service life
  这种模铸聚四氟乙烯环粘合在阀座表面的阀座环槽内，最大限度延长使用寿命。
• Aerospace series - o - ring grooves - design criteria for o - ring grooves , basic calculations aecma technical report tr 4271 : 2000
  航空航天系列. o形环槽. o形环槽设计准则.基本计算
• For motor shafts , the highest stress is at the boundary between the key groove and the ring groove ; the next one is at bottom and terminal of the spline . according to the results , the 17 . 4mm shaft is insecurity , the 22 . 2mm and 30 . 2mm shafts are security
  在轴的安全性上，对17 . 4mm泵轴计算结果是不安全的；对22 . 2mm泵轴计算结果是安全的；对30 . 2mm电机轴计算结果是安全的，而且还有较大的功率输出空间。
• The dynamo runs at rull speed to drive main shaft , then the main shaft makes the emulsifying wings in emulsification grove rotate , which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove . the vanes spins circularly at high speed with the main shatf as center , and the blade and emulsificaton groove cut and crush it continuously . after that . it gers squeezed by the vanes highspeed centrifugal rotation . at last , it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing
  由电动机全速运转带动主轴，经主轴转动乳化框槽内之乳化翼片，使其将桶槽内之液体经框槽上、下两侧之导流叶片吸入环状框槽内，经以主轴为中心高速圆周旋转叶片；连续使乳化翼端刀面与乳化框间极小之间系高频率之强力切割剪断、粉碎，再借叶片高速离心旋转排挤，持续循环混合，以极短之时间即可完成均质乳化之处理。
• For the 30 . 2mm shaft , there are still larger over measure to load . the strength is increased by optimization . for ? 17 . 4mm shaft , the strength is increased by enlarge the inner dimension of the spline ; for 30 . 2mm shaft , the strength is increased by adjust the structure at the boundary between the key groove and the ring groove , the highest stress of the shaft is at bottom and terminal of the spline after optimization
  其中对17 . 4mm泵轴的优化，通过增大花键内径，提高了花键齿底的强度，降低了应力集中点附近的应力；对30 . 2mm电机轴的优化，通过在轴承键的环槽端增加倒角，有效降低了该位置的应力集中，使轴的最大应力点从轴承键与环槽的交界处转变到花键根部与收尾的交界处，提高了电机轴整体结构强度的合理性。